A commercial van tyre inspection checklist helps drivers identify safety-critical defects before a vehicle leaves the depot and gives fleet managers a consistent way to record pressure, tread, damage, load suitability, and replacement decisions. Use this guide for daily walkarounds, scheduled inspections, vehicle handovers, and seasonal fleet reviews.
Overview
Van tyres work under changing conditions: payloads vary, kerbs and loading bays can cause damage, and repeated short journeys may accelerate wear. A reliable inspection routine should therefore cover more than visible tread. It should confirm that each tyre is correctly inflated, suitable for the vehicle’s axle loads, free from dangerous damage, and supported by an accurate maintenance record.
Always use the vehicle manufacturer’s handbook, tyre placard, fleet policy, and applicable local inspection requirements as the controlling references. The figures printed on a tyre sidewall are not a substitute for the vehicle’s specified cold inflation pressures. Pressure recommendations can differ between front and rear axles and may change when the van is heavily loaded.
The following routine is designed for commercial van tyres, including standard, reinforced, extra-load, and run-flat applications where approved by the vehicle manufacturer. It is a management framework, not a replacement for a qualified tyre inspection or repair.
Checklist by scenario
Daily pre-use walkaround
Drivers should complete the check before the first journey, preferably when the tyres are cold and the vehicle is on reasonably level ground. A quick inspection should include:
- Confirm that all fitted tyres appear correctly inflated. Do not rely only on appearance; check with a calibrated pressure gauge when required by the fleet procedure.
- Look across the complete tread and both visible sidewalls for cuts, bulges, exposed cords, splits, embedded objects, or separation.
- Check for uneven wear, bald patches, shoulder wear, or tread blocks that appear damaged or loose.
- Inspect the valve area and valve cap for damage, leakage, or missing components.
- Check that wheels are not visibly cracked, heavily corroded, bent, or contaminated with material that could affect secure fastening.
- Look for fresh tyre marks, fluid, or unusual debris that may indicate a recent puncture or mechanical problem.
- Confirm that the vehicle is not overloaded and that cargo is secured. A correctly rated tyre can still be unsafe if the axle or vehicle load is exceeded.
Printable daily record: Vehicle registration or fleet number: ______ Date: ______ Driver: ______ Odometer: ______
Front left: pass / defect Front right: pass / defect Rear left: pass / defect Rear right: pass / defect Spare: pass / defect. Notes and action taken: __________________________________________
Weekly or scheduled inspection
A more detailed inspection should be completed at the interval set by the fleet operator, with greater frequency for high-mileage, heavily loaded, or rough-route vehicles. Record measured values rather than writing only “OK”.
| Item | What to check | Record |
|---|---|---|
| Tread | Measure tread across the relevant grooves and compare wear across the tyre. | Depth and pattern |
| Pressure | Check cold pressure against the vehicle placard or handbook for the axle and operating load. | Measured pressure |
| Damage | Inspect tread, sidewalls, bead area, and inner sidewalls where access allows. | None or details |
| Valve condition | Check valve stems, caps, extensions, and visible signs of leakage. | Pass or repair |
| Alignment indicators | Look for consistent shoulder wear, feathering, or one-sided wear. | Monitor or investigate |
| Wheel security | Follow the fleet’s approved process for checking fasteners; do not improvise torque settings. | Checked by / date |
| Age and history | Review the tyre identification, fitting date, repair history, and replacement plan. | Update record |
Before a long route, seasonal change, or heavy load
Repeat the daily inspection and verify the planned load against the van’s permitted limits. Confirm that the tyre’s load index is appropriate for the axle position and that the speed rating meets the vehicle requirement. Do not select a replacement solely because its dimensions match; the load rating, construction, approved fitment, and intended use also matter.
Before winter operations or a seasonal changeover, inspect stored tyres for cracking, deformation, contamination, and incorrect labelling. Keep a record of which tyres were fitted to which axle. The seasonal tyre storage and changeover checklist can support this process.
What to double-check
Load rating and pressure
The load index is a coded value that indicates the tyre’s permitted load under specified conditions; it is not the same as the tyre’s inflation pressure. Check the complete tyre marking and compare it with the vehicle manufacturer’s approved specification. Reinforced or extra-load tyres should be fitted only where they are suitable for the vehicle and wheel.
Use the pressure shown on the vehicle placard or in the handbook, usually found near the driver’s door area, fuel flap, or inside the handbook. Check pressures when the tyres are cold. If a tyre is hot after driving, do not release air simply to reach the cold target. Record any adjustment and recheck according to the fleet procedure.
Defect-severity decision tree
- Is there a bulge, exposed cord, major cut, separated tread, rapid pressure loss, or suspected structural damage? If yes, do not send the vehicle out. Isolate it and arrange an assessment by a competent tyre professional.
- Is the tyre significantly underinflated, punctured, or repeatedly losing pressure? If yes, remove it from normal service until the cause is identified and the tyre is inspected.
- Is there uneven wear, a valve fault, a missing cap, or a damaged wheel? If yes, record the defect and arrange prompt corrective work. Consider alignment, suspension, or loading causes rather than replacing only the visibly worn tyre.
- Is the issue cosmetic or minor with no apparent safety impact? Record it, monitor it, and set a review date. Never dismiss a change that is worsening or difficult to classify.
When in doubt, treat the vehicle as unavailable until it has been assessed. A driver should not be expected to diagnose internal tyre damage at the roadside.
Maintenance-record template
Maintain one record per vehicle or use a fleet system with the same fields:
- Vehicle or registration number: ______
- Tyre position: ______
- Brand, pattern, size, load index, and speed rating: ______
- Fitting date and odometer: ______
- Inspection date and inspector: ______
- Measured pressure and tread depth: ______
- Damage, repair, valve, wheel, or alignment notes: ______
- Action taken, supplier, and invoice or job reference: ______
- Replacement date, removal reason, and odometer: ______
- Next inspection or review date: ______
This history helps identify repeat punctures, premature shoulder wear, pressure losses, and tyres that are being removed for different reasons. For tread and age considerations, see the tyre tread depth and age replacement workflow.
Common mistakes
- Checking pressure by sight: A tyre can look acceptable while being materially underinflated. Use a suitable gauge.
- Using the maximum sidewall pressure as the target: The sidewall marking is not normally the vehicle’s recommended operating pressure.
- Measuring only the outer shoulder: Uneven wear can leave the centre or inner shoulder in a different condition.
- Ignoring the inner sidewall: Kerb damage and rubbing may be hidden from a casual walkaround. Inspect from a safe position and use a professional inspection where access is limited.
- Mixing specifications without checking approval: Matching width and diameter alone does not confirm load capacity, construction, clearance, or compatibility.
- Replacing one tyre without considering the axle: Ask a qualified professional about matching, rotation, and the vehicle manufacturer’s requirements.
- Recording only defects: A consistent pass record is useful evidence that inspections are actually taking place and makes trends easier to spot.
For replacement planning, compare the complete specification rather than choosing only by price. The guide to premium versus budget tyres provides a framework for considering durability, use, and total operating cost.
When to revisit
Review this checklist before each seasonal planning cycle, whenever vehicles or tyre suppliers change, and after introducing new inspection software or driver procedures. Update the pressure and load worksheet whenever a vehicle model, axle configuration, wheel, or tyre specification changes. Reconfirm local inspection and recordkeeping requirements periodically rather than relying on an old fleet form.
Fleet managers should also review records after repeated punctures, uneven wear, route changes, unusual loading patterns, or a rise in roadside failures. At the review, identify vehicles with overdue inspections, tyres approaching planned replacement, unresolved defects, or incomplete fitting dates.
Practical next step: Save this page with the fleet inspection procedure, print the daily walkaround section, and create one record for every van. Before the next vehicle leaves the depot, check all four road tyres, confirm the pressure source, record any defect, and stop the vehicle from operating if the tyre’s safety is uncertain.