Fleet tyre cost per mile is more useful than the invoice total alone. This guide provides a repeatable worksheet for comparing commercial tyres, recording fitting and downtime costs, allowing for retreads where appropriate, and deciding when a tyre should be inspected, repaired, replaced, or removed from service.
Overview
A tyre that costs less to buy is not automatically the lowest-cost option for a fleet. The meaningful comparison is the total cost of keeping that tyre in service over a defined distance. That total may include the purchase price, fitting, balancing, valves, inspections, puncture repairs, premature removals, disposal, downtime, and any measurable effect on fuel consumption.
Use cost per mile, or cost per kilometre where that is your fleet’s standard, to compare like with like. Keep vehicle type, axle position, route, load, pressure-management practices, and measurement period visible in the record. A tyre used on a lightly loaded regional van should not be judged directly against one fitted to a heavily loaded vehicle on construction-site routes.
For a practical fleet record, create one line for each tyre position or tyre set and record:
- Vehicle identification, axle position, tyre size, load index, and speed rating.
- Brand, model, casing type, purchase date, and supplier.
- Fitting date, starting odometer, removal odometer, and reason for removal.
- Purchase, fitting, repair, retread, disposal, and downtime costs.
- Total miles or kilometres completed and any relevant fuel or damage notes.
Before ordering commercial tyres, confirm the vehicle maker’s fitment requirements and the tyre’s load rating. The commercial van tyre inspection checklist can help standardise pressure, load-rating, and fleet-record checks.
How to estimate fleet tyre cost per mile
Start with the basic calculation:
Tyre cost per mile = total attributable tyre cost ÷ completed miles
For kilometres, replace “miles” with “kilometres”. The calculation is simple; the difficult part is defining “total attributable tyre cost” consistently.
A useful worksheet formula is:
Total attributable cost = purchase price + fitting and balancing + repairs + retreading + disposal + downtime + fuel-related cost
Not every fleet can measure every category precisely. If fuel impact or downtime is unavailable, leave it out rather than inserting an unsupported estimate. Label the result as a direct tyre cost per mile, then add broader operating costs when reliable data becomes available.
For a tyre that is removed before its expected service period, calculate both the actual cost per mile and the reason for removal. A puncture, sidewall damage, irregular wear, tread reaching the fleet’s internal limit, and a vehicle being sold are different outcomes. Combining them can make a supplier or route appear worse or better than it really is.
For tyre sets, use the distance travelled by the vehicle during the period only when all tyres were fitted for that full period. If individual tyres were changed at different odometer readings, calculate each casing separately. This avoids overstating mileage for a replacement tyre that entered service halfway through the vehicle’s operating period.
Inputs and assumptions for the worksheet
Purchase and workshop costs
Record the invoice cost separately from fitting, balancing, valve replacement, and any wheel or sensor work. If a supplier gives a package price, request a breakdown or record the package as one defined cost. Keep taxes, delivery charges, rebates, and credits treated the same way across all suppliers.
Distance and service life
Use odometer readings, telematics, or a controlled fleet log. Do not use a catalogue mileage expectation as the completed distance. Service life depends on alignment, inflation, axle position, load, driving style, route surface, weather, and maintenance quality.
Repairs, punctures, and damage
Record the number and cost of puncture events, emergency call-outs, valve failures, casing damage, and wheel-related incidents. A tyre with a low purchase cost but frequent roadside events may have a higher operational cost than its invoice suggests. Only repairs approved for the tyre’s condition and permitted by applicable requirements should be included; an unsafe tyre must not be kept in service to improve a spreadsheet result.
Retreading
Where retreading is suitable for the casing and accepted by the fleet’s operating requirements, record the retread cost, inspection cost, additional fitting, and the mileage achieved after retreading. Keep the original casing history attached to the retread record. Do not assume that every casing is retreadable or that a retread will produce the same service life as the original tread.
Downtime and fuel
Downtime can be recorded as the cost of a substitute vehicle, missed work, driver time, recovery, or another internally agreed measure. Use one method consistently. For fuel, compare vehicles operating on similar routes and loads, and avoid attributing every change in consumption to tyres. If the evidence is weak, report fuel impact as unmeasured rather than presenting a false precision.
Replacement rules
Set two thresholds: a safety threshold and an economic threshold. The safety threshold covers damage, pressure loss, exposed structure, abnormal wear, age or condition concerns, and tread depth or inspection requirements applicable to the vehicle’s location. The economic threshold identifies a tyre that remains usable but is costing more through irregular wear, repeated repairs, or poor casing performance than a planned replacement would.
Fleet policy should never override a required inspection or a qualified technician’s decision. For background on condition, age, and tread checks, see the tyre tread depth and age replacement workflow.
Worked examples
Example 1: direct tyre cost
Assume one commercial tyre costs 210 currency units, fitting and balancing cost 25, one repair costs 18, and disposal costs 7. The tyre completes 42,000 miles. The calculation is:
(210 + 25 + 18 + 7) ÷ 42,000 = 260 ÷ 42,000 = 0.0062 currency units per mile
In this example, the direct cost is approximately 0.62 currency units per 100 miles. The figure is only useful if other tyre options are measured using the same inclusions and distance basis.
Example 2: an early removal
Assume a second tyre has the same purchase and fitting costs but is removed after 18,000 miles because of damage. If there are no repair or disposal costs, its cost is 235 ÷ 18,000, or approximately 0.0131 currency units per mile. The result should be tagged “damage removal”, not treated as normal wear. Review the route, wheel condition, pressure records, and incident history before using it to reject an entire tyre model.
Example 3: comparing a retread pathway
For a casing that completes 55,000 miles before retreading, add the original purchase and fitting costs, casing inspection, retread, second fitting, and disposal at final removal. Divide the combined total by the original miles plus retread miles. Compare this result with a new-tyre pathway over a similar distance and duty cycle. Include casing rejection rates, not just successful retreads, so the comparison reflects the whole procurement process.
When to recalculate and what to do next
Recalculate fleet tyre cost per mile monthly for active monitoring and at least quarterly for procurement reviews. Revisit the assumptions sooner when tyre prices, delivery charges, workshop rates, fuel costs, routes, average loads, mileage, or supplier terms change. Also recalculate after introducing a new vehicle type, tyre size, axle configuration, pressure-management system, or retread policy.
At each review, sort the worksheet by cost per mile, removal reason, vehicle, route, axle position, and supplier. Look for repeated patterns: shoulder wear may point to pressure or alignment issues; centre wear may indicate overinflation; frequent punctures may be route-related; and uneven results between vehicles may reveal inconsistent inspections or load distribution.
- Export invoices, odometer readings, inspection records, and repair logs.
- Check that every entry uses the same distance unit and cost categories.
- Separate safety removals, damage removals, planned replacements, and vehicle disposals.
- Compare suppliers on total cost, availability, casing support, warranty handling, delivery reliability, and technical support—not purchase price alone.
- Set the next review date and assign responsibility for updating the worksheet.
Use the result as a procurement aid, not as a reason to delay necessary maintenance. Correct fitment, load rating, inflation, inspection, and safe removal remain the foundation of commercial tyre planning. For related fitment checks, see how to read tyre sizes and confirm fitment.